• 10 dec 2017: forum version update. In case of issues use this topic.
  • 30 nov 2017: pilight moved servers. In case of issues use this topic.
Hello There, Guest! Login Register


Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Basic testing pilight hardware
#1
Hi,

Recently I have bought and soldered the full PCB from the pilight store and mounted it on the GPIO pins of my Pi3B+. After that I have changed the config to reflect that I have a Pi 3 and added the gpio430 hardware settings with 0 and 1 that should correspond with pins 11 & 12 that should be the ones the PCB is wired to.

My next step would be to find put if the hardware is working but this proves to be much harder than expected. I have tried running pilight-debug and it does sporadically receive some data, but when I use my APC3 kaku remote it does not react at all.  

What would be a good way to test if the PCB has been soldered correctly and the hardware is working? Are there some sensible diagnostical steps?

Kind regards,

Dirk
 
Reply
#2
Just check if you see a reasonable input change in pilight-raw when pushing a button on a 433.92Mhz device.
 
Reply
#3
(06-05-2018, 10:11 PM)curlymo Wrote: Just check if you see a reasonable input change in pilight-raw when pushing a button on a 433.92Mhz device.

I do not see any immediate change as a result of sending signals with the remote. Signals do appear eventually though using pilight-raw. These are 3 pulse signals same as the remote produces. Should pilight-raw show output immediately or does it periodically output what it received?
 
Reply
#4
Immediatly.
 
Reply
#5
(06-06-2018, 05:28 PM)curlymo Wrote: Immediatly.

Ok, that is not what I am seeing, though I get other raw signals. How would you recommend debugging this? I have no idea how to eliminate possible issues with the PCB. 
- Power seems ok since it gets raw signals. 
- GPIO wiring also seems ok (gpio433 0,1 should work by default I read)
- Can it be the kaku remote?
- Buy a pre soldered PCB as well and compare?
- Use an external USB sender receiver and compare?
I would really appreciate a nudge in the right direction and would be more than happy to share my findings should I find out what is wrong.
 
Reply
#6
I would first check with directly connection the sender/receiver to the pi.
 
Reply
  


Possibly Related Threads...
Thread Author Replies Views Last Post
  [Fixed] RaspberryPi4 pilight 8.1.5 - Send isn't working DominikB1993 4 50 10-18-2019, 10:25 PM
Last Post: DominikB1993
  Real 433Mhz Remote is disturbed by pilight service henne111 2 158 10-06-2019, 06:18 PM
Last Post: wo_rasp
Tongue (solved) pilight 8.1.5-1-gc0a175e0 Chrashes fleisch 5 584 10-03-2019, 01:15 PM
Last Post: fleisch
  Starting pilight on boot: "cannot bind to the SSDP multicast network" pilino1234 4 347 09-29-2019, 02:08 PM
Last Post: tomk
  pilight for Raspbian Buster (raspberry pi 4) ? starob 29 2,458 07-15-2019, 08:45 PM
Last Post: curlymo
  pilight-receive Filteroption not working Alex 2 569 07-14-2019, 08:35 AM
Last Post: Alex
  pilight usb nano format conversion ettman8 2 452 07-14-2019, 08:32 AM
Last Post: curlymo
  pilight 8.1.4 crashes after some hours Ulrich.Arnold 47 2,697 06-29-2019, 08:58 PM
Last Post: curlymo
  Raspberry PI, gpio-ir-tx and pilight not starting lordslash 5 865 06-11-2019, 05:19 PM
Last Post: curlymo
  pilight fails starting on boot Alex 5 757 06-09-2019, 06:02 PM
Last Post: curlymo

Forum Jump:


Browsing: 1 Guest(s)