[sandnabba]

EDIT: Updating title with protocol info

Hello!

I've recently bought a set of Telldus "Climate Sensors", which look very similar to many of the other tfa2017 sensors.
However, they don't even show up using pilight-debug, so something might be different.

Here is the output from "pilight-raw", 4 times:

Code:

521 904 558 906 552 916 536 927 537 945 1494 939 516 958 1481 957 1481 958 504 973 1470 970 1470 967 1471 979 1460 979 487 972 489 977 487 992 1446 987 1461 981 1465 972 485 987 1453 989 1451 988 1455 990 1447 1000 1444 986 473 993 475 992 1462 980 1451 995 1440 992 480 990 473 988 1460 985 1452 987 474 991 1450 995 1443 994 474 990 472 995 1453 991 473 994 1443 998 1451 992 1439 429070

920 529 929 1504 952 511 945 1492 959 1479 957 503 968 1471 977 1463 969 1471 970 1463 979 492 971 490 990 479 978 1462 987 1455 986 1454 983 515 959 1448 987 1451 991 1451 991 1451 995 1439 997 474 991 472 991 1451 1002 1449 986 1443 997 470 990 477 990 1451 992 1450 993 1440 998 473 1000 1442 1007 1433 1007 462 989 475 985 472 1000 1455 986 471 992 471 896986

527 892 561 906 546 918 541 936 525 939 1500 938 575 902 1487 954 4377 1127 878 1481 935 1461 981 1464 977 484 977 486 1023 451 967 1464 986 1457 980 1457 987 484 987 1449 986 1451 998 1448 989 1450 998 1443 991 472 991 472 992 1452 990 1453 995 1451 984 475 986 482 990 1451 990 1449 996 1445 988 474 994 1449 993 1452 987 472 995 483 978 475 999 1449 990 472 988 470 4422472

504 892 564 909 540 924 536 925 533 933 1504 940 524 948 1490 954 1481 957 506 968 1473 967 1473 974 1460 978 1463 979 484 981 492 3417 513 1083 1348 968 1459 978 481 986 1456 1004 1443 987 1452 992 1447 991 1448 995 480 978 476 1000 1440 1000 1441 1001 1446 993 469 999 1441 993 472 992 473 989 476 989 476 995 1450 986 475 999 464 999 1451 990 1450 990 472 989 473 987 477 1033801

I have very little experience developing pilight and its plugins, so please tell me if there is anything more you need.

Best regards,

Emil

[sandnabba]

I have been digging a little, and I have found out that the protocol is called Alecto V3, and it is supported by the RFLink gateway using this driver:
github.com/seahu/rflink/blob/4d17bd1e7e123aa27433c194382f8a45fecdeda7/Plugins/Plugin_031.c

Not sure if it's possible to convert the code in an easy way, but it's a lot of information about the protocol in the comments. 

Best regards

Emil