• 10 dec 2017: forum version update. In case of issues use this topic.
  • 30 nov 2017: pilight moved servers. In case of issues use this topic.
Hello There, Guest! Login Register


QUIGG GT9000 (Globaltronics/ALDI)
New to forum.
I bought the GT-9000 and 4 GT-FSI-07-UK remote control sockets.
One by one they failed, over the years, with a permanently on status.
This was tested with the socked unplugged, and checking for a short between Live In and Live Out.
Opened it up, de-soldered relay, checked and relay appeared to work properly (maybe just the heat fixed it). Soldered back in, tested - working.
Tried others - also permanently on condition.
I thought - if it's just the relay, maybe the contacts are fused closed.
Banged two of the sockets against each other - fixed!
Must have stopped the contacts from being fused together.
Hope this helps anyone with the same problem.
 
Reply
Hi,

does anyone has experience with this one from amazon:

uniTEC 48110 Funkfernschalterset 3+1 Micro weiß

I'm using this pilight version:

Code:
pilight-daemon version v7.0-252-g97d4b57

I don't get them to run with pilight-send.

This is what I get from pilight-receive:

Code:
{
        "message": {
                "id": "F15",
                "unit": 31,
                "state": "off"
        },
        "origin": "receiver",
        "protocol": "rev2_switch",
        "uuid": "0000-b8-27-eb-2dfd89",
        "repeats": 1
}
{
        "message": {
                "binary": "001100110100110100011100",
                "id": 196727,
                "unit": 3,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "quigg_gt9000",
        "uuid": "0000-b8-27-eb-2dfd89",
        "repeats": 1
}

I have tried several protocols, IDs and units - but nothing works for me.

Code:
pilight-send -p quigg_gt9000 -i 196727 -u 3 -f
pilight-send -p quigg_gt9000 -i 196727 -u 3 -t
pilight-send -p rev2_switch -i F15 -u 31 -f
pilight-send -p rev2_switch -i F15 -u 31 -t

Has someone an idea what I'm doing wrong?
 
Reply
hi Guys

So I can confirm what Klaus has just confirmed I have the radio sockets just trained by pilight and protocol so I used quigg_gt1000 and it was just a simple cheap hardware store radio

Sorry for the bad English I've had it translated by Google

Caleus
 
Reply
Hello,

just looked through the code, to get my gt9000 remotes No. 2 and 3 to work. With this patch (GIT 8.1.3) they work as expected (Syscode-Header are 0001 and 0101):

Code:
--- a/libs/pilight/protocols/433.92/quigg_gt9000.c
+++ b/libs/pilight/protocols/433.92/quigg_gt9000.c
@@ -104,10 +104,11 @@
                         0xE, 0xD, 0x1, 0xB, 0x2, 0xA, 0x4, 0x8 };

 static int isSyscodeType1(int syscodetype) {
-       if(syscodetype & 0x13)
-               return 1;
-
-       return 0;
+       switch(syscodetype) {
+         case 1: return 0; break;
+         case 5: return 0; break;
+         default: return 1; break;
+       }
 }

 static int validate(void) {
@@ -229,8 +230,8 @@
 }

 static void createFooter(void) {
-       quigg_gt9000->raw[quigg_gt9000->rawlen-2] = PULSE_QUIGG_FOOTER1;
-       quigg_gt9000->raw[quigg_gt9000->rawlen-1] = PULSE_QUIGG_FOOTER2;
+        quigg_gt9000->raw[quigg_gt9000->rawlen-2] = 300; //PULSE_QUIGG_FOOTER1;
+        quigg_gt9000->raw[quigg_gt9000->rawlen-1] = 2300; //PULSE_QUIGG_FOOTER2;
 }

 static void clearCode(void) {

Regards,
Stefan
 
Reply
Just have an eye on the repeats.

My GT9000 switches work very well. They are from WorkZone (ALDI, LIDL - and have different names in other shops/countries).

You have to send the command multiple times, depending on the repeats:

For example 2 repeats:
Code:
pilight-send -p quigg_gt9000 -i 790312 -u 0 --on && pilight-send -p quigg_gt9000 -i 790312 -u 0 --on

or 3 repeats:
Code:
pilight-send -p quigg_gt9000 -i 790312 -u 0 --off && pilight-send -p quigg_gt9000 -i 790312 -u 0 --off && pilight-send -p quigg_gt9000 -i 790312 -u 0 --off
 
Reply
Any idea what could be done? This is what I get with pilight-receive from the remote:

Code:
{
       "message": {
               "binary": "010000111100110110110000",
               "id": 263153,
               "unit": 0,
               "state": "on"
       },
       "origin": "receiver",
       "protocol": "quigg_gt9000",
       "uuid": "0000-b8-27-eb-97584d",
       "repeats": 1
}
{
       "message": {
               "binary": "110000111100110110110000",
               "id": 787441,
               "unit": 0,
               "state": "on"
       },
       "origin": "receiver",
       "protocol": "quigg_gt9000",
       "uuid": "0000-b8-27-eb-97584d",
       "repeats": 2
}
{
       "message": {
               "binary": "010000111100110110110000",
               "id": 263153,
               "unit": 0,
               "state": "on"
       },
       "origin": "receiver",
       "protocol": "quigg_gt9000",
       "uuid": "0000-b8-27-eb-97584d",
       "repeats": 3
}


But this wont switch the plug on:
Code:
sudo pilight-send -p quigg_gt9000 -i 263153 -u 0 --on

When I run it, this is what pilight-receive gets:
Code:
{
        "origin": "sender",
        "protocol": "quigg_gt9000",
        "message": {
                "id": 263153,
                "unit": 0,
                "state": "on"
        },
        "repeat": 1,
        "uuid": "0000-b8-27-eb-97584d"
}


Should it be >1 repeats? 3-4?
 
Reply
(03-28-2019, 10:43 PM)aP7D1CKD Wrote: Any idea what could be done? This is what I get with pilight-receive from the remote:

Code:
{
       "message": {
               "binary": "010000111100110110110000",
               "id": 263153,
               "unit": 0,
               "state": "on"
       },
       "origin": "receiver",
       "protocol": "quigg_gt9000",
       "uuid": "0000-b8-27-eb-97584d",
       "repeats": 1
}
{
       "message": {
               "binary": "110000111100110110110000",
               "id": 787441,
               "unit": 0,
               "state": "on"
       },
       "origin": "receiver",
       "protocol": "quigg_gt9000",
       "uuid": "0000-b8-27-eb-97584d",
       "repeats": 2
}
{
       "message": {
               "binary": "010000111100110110110000",
               "id": 263153,
               "unit": 0,
               "state": "on"
       },
       "origin": "receiver",
       "protocol": "quigg_gt9000",
       "uuid": "0000-b8-27-eb-97584d",
       "repeats": 3
}


But this wont switch the plug on:
Code:
sudo pilight-send -p quigg_gt9000 -i 263153 -u 0 --on

When I run it, this is what pilight-receive gets:
Code:
{
        "origin": "sender",
        "protocol": "quigg_gt9000",
        "message": {
                "id": 263153,
                "unit": 0,
                "state": "on"
        },
        "repeat": 1,
        "uuid": "0000-b8-27-eb-97584d"
}


Should it be >1 repeats? 3-4?

Just found out that this works as ON command. I captured it with pilight-raw.

Code:
sudo pilight-send -p raw -c "308 2290 307 1205 1056 450 291 1220 294 1260 254 1230 1042 475 1038 467 1048 470 292 1227 1056 456 285 1243 271 1227 1047 468 1044 474 286 1240 277 1225 305 1214 310 1201 1056 454 1044 489 270 1233 285 1232 279 1245 275 1241 277 2375 270 1248 1025 473 287 1226 282 1239 275 1253 1021 475 1048 469 1049 481 272 1240 1031 475 284 1238 337 1179 1036 477 1038 475 305 1220 274 1238 277 1243 273 1257 1016 478 1034 479 278 1243 274 1241 278 1244 271 1248 269 2376 286 1233 1029 482 277 1241 271 1238 280 1233 1043 483 1025 488 1030 481 273 1250 1024 481 276 1247 271 1238 1037 475 1038 489 270 1240 276 1260 253 1244 271 1241 1030 483 1031 480 283 1240 270 1246 269 1242 276 1251 266 2376 267 1236 1037 478 279 1243 271 1247 274 1236 1032 492 1023 486 1030 474 282 1243 1030 480 277 1249 267 1240 1057 456 1028 509 266 1223 276 1246 264 1244 273 1256 1019 479 1048 478 270 1243 274 1267 249 1238 276 1252 2928 7210"
 
Reply
>Just found out that this works as ON command. I captured it with pilight-raw.

See attachment for data of all buttons (1-3 ON/OFF).  Does someone have a vision what it is?


Attached Files
.txt   quigg-gt9001.txt (Size: 5.54 KB / Downloads: 2)
 
Reply
(03-29-2019, 10:35 PM)aP7D1CKD Wrote: >Just found out that this works as ON command. I captured it with pilight-raw.

See attachment for data of all buttons (1-3 ON/OFF).  Does someone have a vision what it is?

Did you try my patch from https://forum.pilight.org/showthread.php...8#pid23788 ?

Stefan
 
Reply
Hey,

new purchased "Heitech" from Amazon (hxxps://www.amazon.de/dp/B00KM83Q1U) are also working with GT9000, but only after applying the last posted patch for the footer.

Hope that will help anyone Smile

Christian
 
Reply
  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Brennenstuhl RCR CE1 1011 with QUIGG GT9000 Protocol scootermacro 1 345 06-27-2019, 06:20 PM
Last Post: scootermacro
  Weather Station Globaltronics GT-WT-01 Prutsky 13 7,205 04-09-2018, 07:34 PM
Last Post: NevelS
  Quigg GT-1000 maartenh 53 25,313 12-05-2016, 03:13 PM
Last Post: Klaus
  quigg gt7000 Dimmer wchristi 11 8,310 04-30-2015, 09:25 AM
Last Post: wo_rasp
  Quigg Screens curlymo 6 4,111 01-31-2015, 07:33 PM
Last Post: curlymo
  QUIGG (Globaltronics/ALDI) neevedr 49 34,017 01-12-2015, 10:01 AM
Last Post: wo_rasp

Forum Jump:


Browsing: 1 Guest(s)