• 10 dec 2017: forum version update. In case of issues use this topic.
  • 30 nov 2017: pilight moved servers. In case of issues use this topic.
Hello There, Guest! Login Register


Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Webgui offline after some hours
#1
Hello, I have big problems with the accessibility of the webgui.

I use the last official version of pilight (not nightly) and everything actually runs wonderfully on a raspberry 3, which is connected to LAN (fixed IP) in the home network.

At least once a day, it is not possible to connect to the webgui via HTTP (browser) and / or SSDP (Android app). However, it is always possible to connect to the Raspberry via Putty. The rules also continue working.
I then have to restart the pilight service manually via SSH (putty) and then it works again in a few hours (10-24) until the next failure.

Sometimes only "pilight webgui" appears in the top left of the browser when loading the webguide.

I really have no idea where to look else. Any suggestions for me?

thanks for your help

Scooter
 
Reply
#2
This issue has been fixed in the latest nightly.
 
Reply
#3
Thank you for the hint!
After some days of testing the latest nightly, I´m afraid the problem is the same as before with the official release.
The only difference is that the time is extended. When webgui was not reachable after some hours it´s now unrechable only once a day or once in 2 days, but still the same thing....

What would help? Other hardware?

Best regards,

Scooter
 
Reply
#4
Can you check the cpu usage of pilight with top when that happens?
 
Reply
#5
PHP Code:
6038 root     -81   0  171520  21960   8044 S   1.0   2.3   4:04.52 pilight-daemon
 6298 pi        20   0   10328   2836   2476 R   0.7   0.3   0
:00.22 top
 6279 pi        20   0   12236   3632   2856 S   0.3   0.4   0
:00.07 sshd
    1 root      20   0   33736   8044   6376 S   0.0   0.8   0
:20.42 systemd
    2 root      20   0       0      0      0 S   0.0   0.0   0
:00.14 kthreadd
    3 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 rcu_gp
    4 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 rcu_par_gp
    8 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 mm_percpu_wq
    9 root      20   0       0      0      0 S   0.0   0.0   0
:11.24 ksoftirqd/0
   10 root      20   0       0      0      0 I   0.0   0.0   0
:19.75 rcu_sched
   11 root      20   0       0      0      0 I   0.0   0.0   0
:00.00 rcu_bh
   12 root      rt   0       0      0      0 S   0.0   0.0   0
:00.04 migration/0
   13 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 cpuhp/0
   14 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 cpuhp/1
   15 root      rt   0       0      0      0 S   0.0   0.0   0
:00.04 migration/1
   16 root      20   0       0      0      0 S   0.0   0.0   0
:00.37 ksoftirqd/1
   19 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 cpuhp/2
   20 root      rt   0       0      0      0 S   0.0   0.0   0
:00.03 migration/2
   21 root      20   0       0      0      0 S   0.0   0.0   0
:08.27 ksoftirqd/2
   24 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 cpuhp/3
   25 root      rt   0       0      0      0 S   0.0   0.0   0
:00.03 migration/3
   26 root      20   0       0      0      0 S   0.0   0.0   0
:00.17 ksoftirqd/3
   29 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 kdevtmpfs
   30 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 netns
   34 root      20   0       0      0      0 S   0.0   0.0   0
:00.34 khungtaskd
   35 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 oom_reaper
   36 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 writeback
   37 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 kcompactd0
   38 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 crypto
   39 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 kblockd
   40 root      rt   0       0      0      0 S   0.0   0.0   0
:00.00 watchdogd
   42 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 rpciod
   43 root       0 
-20       0      0      0 I   0.0   


regards,

Mike
 
Reply
#6
I have no clue.

Can you post your config?
 
Reply
#7
another top from today:

Browser only "pilight webgui" showing
Putty works

PHP Code:
 PID USER      PR  NI    VIRT    RES    SHR S  %CPU  %MEM     TIMECOMMAND
 7712 pi        20   0   10328   3028   2512 R   0.7   0.3   0
:00.52 top
    1 root      20   0   33964   8188   6376 S   0.0   0.9   0
:23.14 systemd
    2 root      20   0       0      0      0 S   0.0   0.0   0
:00.18 kthreadd
    3 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 rcu_gp
    4 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 rcu_par_gp
    8 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 mm_percpu_wq
    9 root      20   0       0      0      0 S   0.0   0.0   0
:13.71 ksoftirqd/0
   10 root      20   0       0      0      0 I   0.0   0.0   0
:23.12 rcu_sched
   11 root      20   0       0      0      0 I   0.0   0.0   0
:00.00 rcu_bh
   12 root      rt   0       0      0      0 S   0.0   0.0   0
:00.05 migration/0
   13 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 cpuhp/0
   14 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 cpuhp/1
   15 root      rt   0       0      0      0 S   0.0   0.0   0
:00.04 migration/1
   16 root      20   0       0      0      0 S   0.0   0.0   0
:00.43 ksoftirqd/1
   19 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 cpuhp/2
   20 root      rt   0       0      0      0 S   0.0   0.0   0
:00.04 migration/2
   21 root      20   0       0      0      0 S   0.0   0.0   0
:09.46 ksoftirqd/2
   24 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 cpuhp/3
   25 root      rt   0       0      0      0 S   0.0   0.0   0
:00.04 migration/3
   26 root      20   0       0      0      0 S   0.0   0.0   0
:00.19 ksoftirqd/3
   29 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 kdevtmpfs
   30 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 netns
   34 root      20   0       0      0      0 S   0.0   0.0   0
:00.40 khungtaskd
   35 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 oom_reaper
   36 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 writeback
   37 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 kcompactd0
   38 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 crypto
   39 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 kblockd
   40 root      rt   0       0      0      0 S   0.0   0.0   0
:00.00 watchdogd
   42 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 rpciod
   43 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 kworker/u9:0-hci0
   44 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 xprtiod
   47 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 kswapd0
   48 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 nfsiod
   59 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 kthrotld
   60 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 iscsi_eh
   61 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 dwc_otg
   62 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 DWC Notificatio
   63 root       1 
-19       0      0      0 S   0.0   0.0   0:00.00 vchiq-slot/0
   64 root       1 
-19       0      0      0 S   0.0   0.0   0:00.00 vchiq-recy/0
   65 root       0 
-20       0      0      0 S   0.0   0.0   0:00.00 vchiq-sync/0
   66 root      20   0       0      0      0 S   0.0   0.0   0
:00.00 vchiq-keep/0
   67 root      10 
-10       0      0      0 S   0.0   0.0   0:00.00 SMIO
   69 root     
-51   0       0      0      0 S   0.0   0.0   0:00.00 irq/86-mmc1
   72 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 mmc_complete
   75 root       0 
-20       0      0      0 I   0.0   0.0   0:00.97 kworker/1:1H-kblockd
   76 root      20   0       0      0      0 S   0.0   0.0   0
:04.91 jbd2/mmcblk0p2-
 
  77 root       0 -20       0      0      0 I   0.0   0.0   0:00.00 ext4-rsv-conver
   79 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 ipv6_addrconf
   82 root       0 
-20       0      0      0 I   0.0   0.0   0:01.30 kworker/3:1H-kblockd
  107 root      20   0   33092  11076  10240 S   0.0   1.2   0
:06.12 systemd-journal
  141 root      20   0   18056   3972   3128 S   0.0   0.4   0
:02.10 systemd-udevd
  162 root      10 
-10       0      0      0 S   0.0   0.0   0:00.00 SMIO
  194 root       0 
-20       0      0      0 I   0.0   0.0   0:00.00 mmal-vchiq 
 
Reply
#8
config.json

Code:
{
    "devices": {
        "zeit": {
            "protocol": [ "datetime" ],
            "id": [{
                "longitude": 15.4643,
                "latitude": 48.3940
            }],
            "year": 2020,
            "month": 5,
            "day": 29,
            "hour": 6,
            "minute": 0,
            "second": 0,
            "weekday": 6,
            "dst": 1
        },
        "sunrisesetdevice": {
            "protocol": [ "sunriseset" ],
            "id": [{
                "longitude": 15.4643,
                "latitude": 48.3940
            }],
            "sunrise": 5.03,
            "sunset": 20.50,
            "sun": "rise"
        },
        "schalter1": {
            "protocol": [ "elro_800_switch" ],
            "id": [{
                "systemcode": 1,
                "unitcode": 1
            }],
            "state": "off"
        },
        "schalter2": {
            "protocol": [ "elro_800_switch" ],
            "id": [{
                "systemcode": 1,
                "unitcode": 2
            }],
            "state": "off"
        },
        "brennenstuhl2": {
            "protocol": [ "elro_800_switch" ],
            "id": [{
                "systemcode": 1,
                "unitcode": 4
            }],
            "state": "off"
        },
        "schalter4": {
            "protocol": [ "quigg_gt1000" ],
            "id": [{
                "id": 1,
                "unit": 3
            }],
            "state": "off"
        },
        "schalter5": {
            "protocol": [ "elro_400_switch" ],
            "id": [{
                "systemcode": 27,
                "unitcode": 23
            }],
            "state": "off"
        },
        "fernseher": {
            "protocol": [ "elro_400_switch" ],
            "id": [{
                "systemcode": 27,
                "unitcode": 15
            }],
            "state": "off"
        },
        "kodi": {
            "protocol": [ "elro_400_switch" ],
            "id": [{
                "systemcode": 27,
                "unitcode": 27
            }],
            "state": "off"
        },
        "brennenstuhl1": {
            "protocol": [ "quigg_gt1000" ],
            "id": [{
                "id": 1,
                "unit": 0
            }],
            "state": "off"
        },
        "schalter3": {
            "protocol": [ "quigg_gt1000" ],
            "id": [{
                "id": 1,
                "unit": 1
            }],
            "state": "off"
        },
        "drucker": {
            "protocol": [ "quigg_gt1000" ],
            "id": [{
                "id": 1,
                "unit": 2
            }],
            "state": "off"
        },
        "sensor1": {
            "protocol": [ "gpio_switch" ],
            "id": [{
                "gpio": 1
            }],
            "state": "off"
        },
        "sensor2": {
            "protocol": [ "gpio_switch" ],
            "id": [{
                "gpio": 12
            }],
            "state": "off"
        },
        "sensor3": {
            "protocol": [ "gpio_switch" ],
            "id": [{
                "gpio": 3
            }],
            "state": "off"
        },
        "sensor4": {
            "protocol": [ "gpio_switch" ],
            "id": [{
                "gpio": 4
            }],
            "state": "off"
        },
        "priorisierung_klima": {
            "protocol": [ "generic_switch" ],
            "id": [{
                "id": 100
            }],
            "state": "off"
        },
        "priorisierung_pool": {
            "protocol": [ "generic_switch" ],
            "id": [{
                "id": 99
            }],
            "state": "on"
        },
        "pumpenach12": {
            "protocol": [ "generic_switch" ],
            "id": [{
                "id": 98
            }],
            "state": "on"
        },
        "regeln_ein": {
            "protocol": [ "generic_switch" ],
            "id": [{
                "id": 97
            }],
            "state": "on"
        }
    },
    "rules": {
        "schalterregel1": {
            "rule": "IF regeln_ein.state == on AND priorisierung_klima.state == on THEN switch DEVICE priorisierung_pool TO off",
            "active": 1
        },
        "schalterregel2": {
            "rule": "IF regeln_ein.state == on AND priorisierung_pool.state == on THEN switch DEVICE priorisierung_klima TO off",
            "active": 1
        },
        "schalterregel3": {
            "rule": "IF regeln_ein.state == off THEN switch DEVICE priorisierung_pool TO off AFTER '1 SECOND' AND switch DEVICE priorisierung_klima TO off AFTER '3 SECOND' AND switch DEVICE pumpenach12 TO off AFTER '5 SECOND'",
            "active": 1
        },
        "druckeraus30min": {
            "rule": "IF regeln_ein.state == on AND drucker.state == on THEN switch DEVICE drucker TO off AFTER '30 MINUTE'",
            "active": 1
        },
        "ueberschussregel1pool": {
            "rule": "IF regeln_ein.state == on AND sensor1.state == on AND priorisierung_pool.state == on THEN switch DEVICE schalter1 TO on AFTER '1 SECOND'",
            "active": 1
        },
        "ueberschussregel2pool": {
            "rule": "IF regeln_ein.state == on AND sensor2.state == on AND priorisierung_pool.state == on THEN switch DEVICE schalter2 TO on AFTER '2 SECOND'",
            "active": 1
        },
        "ueberschussregel3-12Uhrpool": {
            "rule": "IF regeln_ein.state == on AND sensor3.state == on AND priorisierung_pool.state == on AND pumpenach12.state == on AND DATE_FORMAT(zeit, %H%M) > 1200 AND DATE_FORMAT(zeit, %H%M) < 1600 THEN switch DEVICE schalter3 TO on AFTER '3 SECOND'",
            "active": 1
        },
        "ueberschussregel3pool": {
            "rule": "IF regeln_ein.state == on AND sensor3.state == on AND priorisierung_pool.state == on AND pumpenach12.state == off AND DATE_FORMAT(zeit, %H%M) > 0800 THEN switch DEVICE schalter3 TO on AFTER '3 SECOND'",
            "active": 1
        },
        "ueberschussregel4pool": {
            "rule": "IF regeln_ein.state == on AND sensor4.state == on AND priorisierung_pool.state == on THEN switch DEVICE schalter4 TO on AFTER '4 SECOND'",
            "active": 1
        },
        "ueberschussregel1auspool": {
            "rule": "IF regeln_ein.state == on AND sensor1.state == off AND priorisierung_pool.state == on THEN switch DEVICE schalter1 TO off AFTER '1 SECOND'",
            "active": 1
        },
        "ueberschussregel2auspool": {
            "rule": "IF regeln_ein.state == on AND sensor2.state == off AND priorisierung_pool.state == on THEN switch DEVICE schalter2 TO off AFTER '2 SECOND'",
            "active": 1
        },
        "ueberschussregel3auspool": {
            "rule": "IF regeln_ein.state == on AND sensor3.state == off AND priorisierung_pool.state == on THEN switch DEVICE schalter3 TO off AFTER '3 SECOND'",
            "active": 1
        },
        "ueberschussregel4auspool": {
            "rule": "IF regeln_ein.state == on AND sensor4.state == off AND priorisierung_pool.state == on THEN switch DEVICE schalter4 TO off AFTER '4 SECOND'",
            "active": 1
        },
        "ueberschussregel4klima": {
            "rule": "IF regeln_ein.state == on AND sensor4.state == on AND priorisierung_klima.state == on THEN switch DEVICE schalter4 TO on AFTER '1 SECOND'",
            "active": 1
        },
        "ueberschussregel1klima": {
            "rule": "IF regeln_ein.state == on AND sensor1.state == on AND priorisierung_klima.state == on AND schalter4.state == on THEN switch DEVICE schalter1 TO on AFTER '1 SECOND'",
            "active": 1
        },
        "ueberschussregel2klima": {
            "rule": "IF regeln_ein.state == on AND sensor2.state == on AND priorisierung_klima.state == on AND schalter4.state == on THEN switch DEVICE schalter2 TO on AFTER '2 SECOND'",
            "active": 1
        },
        "ueberschussregel3-12Uhrklima": {
            "rule": "IF regeln_ein.state == on AND sensor3.state == on AND priorisierung_klima.state == on AND schalter4.state == on AND pumpenach12.state == on AND DATE_FORMAT(zeit, %H%M) > 1200 AND pumpenach12.state == on AND DATE_FORMAT(zeit, %H%M) < 1600 THEN switch DEVICE schalter3 TO on AFTER '3 SECOND'",
            "active": 1
        },
        "ueberschussregel3klima": {
            "rule": "IF regeln_ein.state == on AND sensor3.state == on AND priorisierung_klima.state == on AND pumpenach12.state == off AND DATE_FORMAT(zeit, %H%M) > 0800 THEN switch DEVICE schalter3 TO on AFTER '3 SECOND'",
            "active": 1
        },
        "ueberschussregel1ausklima": {
            "rule": "IF regeln_ein.state == on AND sensor1.state == off AND priorisierung_klima.state == on THEN switch DEVICE schalter1 TO off",
            "active": 1
        },
        "ueberschussregel2ausklima": {
            "rule": "IF regeln_ein.state == on AND sensor2.state == off AND priorisierung_klima.state == on THEN switch DEVICE schalter2 TO off",
            "active": 1
        },
        "ueberschussregel3ausklima": {
            "rule": "IF regeln_ein.state == on AND sensor3.state == off AND priorisierung_klima.state == on THEN switch DEVICE schalter3 TO off",
            "active": 1
        },
        "ueberschussregel4ausklima": {
            "rule": "IF regeln_ein.state == on AND sensor4.state == off AND priorisierung_klima.state == on THEN switch DEVICE schalter4 TO off",
            "active": 1
        },
        "sunset": {
            "rule": "IF regeln_ein.state == on AND (sunrisesetdevice.sunset == DATE_FORMAT(DATE_ADD(zeit, '+1 HOUR'), '%Y-%m-%d %H:%M:%S', %H.%M))THEN switch DEVICE schalter1 TO off AND switch DEVICE schalter2 TO off AND switch DEVICE schalter3 TO off",
            "active": 1
        }
    },
    "gui": {
        "drucker": {
            "name": "Druckerli und Kellerinternetili",
            "group": [ "Schalter" ],
            "media": [ "all" ]
        },
        "fernseher": {
            "name": "Wohnzimmer Fernseherli",
            "group": [ "Schalter" ],
            "media": [ "all" ]
        },
        "kodi": {
            "name": "Kodi Entertainment",
            "group": [ "Schalter" ],
            "media": [ "all" ]
        },
        "brennenstuhl1": {
            "name": "Fernseher Papa",
            "group": [ "Schalter" ],
            "media": [ "all" ]
        },
        "brennenstuhl2": {
            "name": "Garten Internet",
            "group": [ "Schalter" ],
            "media": [ "all" ]
        },
        "schalter5": {
            "name": "Handy Ladegeraet",
            "group": [ "Schalter" ],
            "media": [ "all" ]
        },
        "schalter1": {
            "name": "Keller Kuehlschrank",
            "group": [ "Lastmanagement" ],
            "media": [ "all" ]
        },
        "schalter2": {
            "name": "Entfeuchter",
            "group": [ "Lastmanagement" ],
            "media": [ "all" ]
        },
        "schalter3": {
            "name": "Poolpumpe",
            "group": [ "Lastmanagement" ],
            "media": [ "all" ]
        },
        "schalter4": {
            "name": "Klimaanlage",
            "group": [ "Lastmanagement" ],
            "media": [ "all" ]
        },
        "sunrisesetdevice": {
            "name": "Sonne von ...",
            "group": [ "Lastmanagement", "Schalter" ],
            "media": [ "all" ]
        },
        "sensor1": {
            "name": "Ueberschuss Schwelle 1",
            "group": [ "Lastmanagement" ],
            "media": [ "all" ]
        },
        "sensor2": {
            "name": "Ueberschuss Schwelle 2",
            "group": [ "Lastmanagement" ],
            "media": [ "all" ]
        },
        "sensor3": {
            "name": "Ueberschuss Schwelle 3",
            "group": [ "Lastmanagement" ],
            "media": [ "all" ]
        },
        "sensor4": {
            "name": "Ueberschuss Schwelle 4",
            "group": [ "Lastmanagement" ],
            "media": [ "all" ]
        },
        "regeln_ein": {
            "name": "Alle Regeln aktiv",
            "group": [ "Prioritäten" ],
            "media": [ "all" ],
            "confirm": 1
        },
        "priorisierung_pool": {
            "name": "Pool priorisieren",
            "group": [ "Prioritäten" ],
            "media": [ "all" ],
            "confirm": 1
        },
        "pumpenach12": {
            "name": "Poolpumpe nach 12 Uhr",
            "group": [ "Prioritäten" ],
            "media": [ "all" ],
            "confirm": 1
        },
        "priorisierung_klima": {
            "name": "Klimaanlage priorisieren",
            "group": [ "Prioritäten" ],
            "media": [ "all" ],
            "confirm": 1
        }
    },
    "settings": {
        "log-level": 6,
        "pid-file": "/var/run/pilight.pid",
        "log-file": "/var/log/pilight.log",
        "standalone": 0,
        "webgui-websockets": 1,
        "webserver-enable": 1,
        "webserver-root": "/usr/local/share/pilight/webgui",
        "webserver-http-port": 5001,
        "webserver-cache": 1,
        "whitelist": "",
        "gpio-platform": "raspberrypi3"
    },
    "hardware": {
        "433gpio": {
            "sender": 31,
            "receiver": 13
        }
    },
    "registry": {
        "hardware": {
            "RF433": {
                "mingaplen": 4420,
                "maxgaplen": 72900,
                "minrawlen": 26,
                "maxrawlen": 400
            }
        },
        "pilight": {
            "version": {
                "current": "8.1.5"
            }
        },
        "webserver": {
            "ssl": {
                "certificate": {
                    "location": "/etc/pilight/pilight.pem"
                }
            }
        }
    }
}
 
Reply
#9
What was the last working version?
 
Reply
#10
(05-29-2020, 08:17 AM)curlymo Wrote: What was the last working version?

It always worked (with the same problem). I`m in since 8.1

Actually I´m replacing hardware step by step... I`m just trying to use another charger after that another SD-Card, then another Raspi ..... maybe ... no clue too

Best regads & thank you

Scooter
 
Reply
  


Possibly Related Threads...
Thread Author Replies Views Last Post
  WebGUI emtpy since 8.0.8 Dergo 14 3,590 02-24-2018, 01:09 PM
Last Post: Dergo
  CONTACT devices | Webgui wupperpi 2 1,029 01-18-2018, 03:37 PM
Last Post: wupperpi
  [solved] Webgui 404-Error PT-Biker 2 1,346 11-11-2017, 09:49 AM
Last Post: PT-Biker
  pilight doesn't show the right status in webgui jurkla 8 3,225 11-17-2016, 09:41 AM
Last Post: gregnau
  pilight WebGui not working after reboot Frank_a 7 5,394 02-04-2016, 09:11 AM
Last Post: wo_rasp
  [pilight 7] Got no buttons on the WebGUI Nachtwind 2 2,753 07-29-2015, 08:16 PM
Last Post: Nachtwind
  Running pilight offline Aweponken 11 6,469 07-20-2015, 07:12 PM
Last Post: Aweponken
Question [nightly build] getting datetime in webgui questor 1 2,342 12-29-2014, 03:46 PM
Last Post: curlymo
  webgui/ssh very slow .. high cpu usage gneandr 1 2,685 10-01-2014, 06:43 PM
Last Post: creamers
  Help needed, webgui not loading -Solved- puuhapet 18 14,062 09-16-2014, 09:58 AM
Last Post: puuhapet

Forum Jump:


Browsing: 1 Guest(s)