• 10 dec 2017: forum version update. In case of issues use this topic.
  • 30 nov 2017: pilight moved servers. In case of issues use this topic.
Hello There, Guest! Login Register


[Fully Supported] Conrad RSL Contact Sensor
#41
I just bought the same door contacts. Did anybody already implement the protocol? In pilight-receive I just get the conrad_rsl_switch protocol. The contacts have a learning function, which is described in the documentation: http://www.produktinfo.conrad.com/datenb..._fr_nl.pdf
Does anybody now how the learning works? I can press a button and the contact keeps sending the same code as long as I hold the button. It says id 6 and unit 5. According to the conrad_rsl_switch protocol id 6 is out of range. Does anybody manage to teach these contact sensors an id and unit?
 
Reply
#42
Hi, I also get the "invalid id range" error when sending with "conrad_rsl_switch" id=6 and unit=5.
The forum clearly shows that I am not alone with this problem.
Any progress, tips, or tricks? Thanks!

Calling:
http://192.168.10.123:5001/send?protocol...d=6&unit=5

Causes:
pilight-daemon: ERROR: conrad_rsl_switch: invalid id range

It seems that sending with ID > 5 causes the out of range although pilight-receive shows:

"message": {
"id": 6,
"unit": 5,
"state": "off"
},
"origin": "receiver",
"protocol": "conrad_rsl_switch",
"uuid": "0000-b8-27-eb-efe866",
"repeats": 9
}

Package: pilight | Architecture: armhf | Version: 7.0.49-g6ed7da9
 
Reply
#43
A tip: Use code tags, otherwise you'll get very few responses Wink

I've had a look, and although the regex for the ID looks like somebody rolled their face on a keyboard, it does accept numbers above 5. I'm not sure why it doesn't work.
 
Reply
#44
Hi,

having trouble with the contact sensors too (and I'm new to pilight too).

After activting the window contact I get the following output in pilight-receive:

Code:
pi@raspberrypi ~ $ sudo pilight-receive
{
        "message": {
                "all": 1,
                "unit": 2,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "conrad_rsl_switch",
        "uuid": "0000-00-0c-f6-568858",
        "repeats": 1
}
{
        "message": {
                "all": 1,
                "unit": 2,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "conrad_rsl_switch",
        "uuid": "0000-00-0c-f6-568858",
        "repeats": 2
}
{
        "message": {
                "all": 1,
                "unit": 2,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "conrad_rsl_switch",
        "uuid": "0000-00-0c-f6-568858",
        "repeats": 3
}
{
        "message": {
                "all": 1,
                "unit": 2,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "conrad_rsl_switch",
        "uuid": "0000-00-0c-f6-568858",
        "repeats": 4
}

and a few seconds later (after the contact switch sends the "off" signal):

Code:
{
        "message": {
                "all": 1,
                "unit": 2,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "conrad_rsl_switch",
        "uuid": "0000-00-0c-f6-568858",
        "repeats": 1
}
{
        "message": {
                "all": 1,
                "unit": 2,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "conrad_rsl_switch",
        "uuid": "0000-00-0c-f6-568858",
        "repeats": 2
}
{
        "message": {
                "all": 1,
                "unit": 2,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "conrad_rsl_switch",
        "uuid": "0000-00-0c-f6-568858",
        "repeats": 3
}
{
        "message": {
                "all": 1,
                "unit": 2,
                "state": "on"
        },
        "origin": "receiver",
        "protocol": "conrad_rsl_switch",
        "uuid": "0000-00-0c-f6-568858",
        "repeats": 4
}

2 Questions from my side:

a) is it correct that both signals show as "on"?
b) what do I need to enter in the devices object of "/etc/pilight/config.json"?

pilight was freshly installed from the repository (reports as pilight v7.0 / filter firmware v1 in the WebGUI). I'm using the Arduino nano USB receiver.

Update 9.11.:
The contact sensor still shows as sending "on" in both cases. That makes it not too easy to use.
Gave it another try with a 2nd contact sensor. That one isn't shown in pilight-receive once the contact is triggered. But I can see it when I hold the pair button. If added to the devices and GUI it obviouly doesn't get registered in the WebGUI.

Any suggestios are much appreviated.
 
Reply
  


Possibly Related Threads...
Thread Author Replies Views Last Post
  [Partially Supported] TFA / Conrad Weather Yves 203 17,206 03-27-2020, 01:21 PM
Last Post: Ascenion
  [Fully Supported] KlikAanKlikUit Motion Sensor koen01 37 13,448 03-26-2020, 02:46 PM
Last Post: Gisto
  Digoo / Baldr / Nexus / Rubicson temperature/humidity sensor thielj 12 2,258 02-10-2020, 10:54 PM
Last Post: ha_username
  Support for Temperaturee sensor clona 4 199 02-10-2020, 02:52 PM
Last Post: clona
  gs-iwds07 window sensor Loggisch 48 14,990 12-09-2019, 07:14 PM
Last Post: curlymo
Lightbulb [Fully Supported] Kaku Door sensor (AMST-606) geerttttt 53 26,387 10-19-2019, 06:26 PM
Last Post: curlymo
  433MHz PIR sensor from Amazon ha_username 0 400 09-29-2019, 11:44 PM
Last Post: ha_username
  [Fully Supported] DHT22 IcedEarth 86 34,135 11-18-2018, 09:33 AM
Last Post: curlymo
  Pearl weatherstation sensor for FWS-686 & FWS-665 chklump 13 5,624 08-12-2018, 05:34 PM
Last Post: fourty2
  TFA 30.3160 Pool Sensor wseifert 4 1,183 05-30-2018, 09:24 AM
Last Post: wseifert

Forum Jump:


Browsing: 1 Guest(s)