• 10 dec 2017: forum version update. In case of issues use this topic.
  • 30 nov 2017: pilight moved servers. In case of issues use this topic.
Hello There, Guest! Login Register


QUIGG (Globaltronics/ALDI)
#11
After pressing three time the same button i receive 9 code grouped by three patterns:

Code:
510 1023 476 1030 487 1066 452 1030 507 1039     971 528 1001 535 494 1040 986 540 989 545         1000 533 993 543 480 1088 1015 542 948 540         973 558 982 527 478 1055 980 534 483 1052         484 1043 485 1041 483 1054 479 1038 3029 7042 0
487 1046 473 1022 533 1002 499 1032 496 1027     1014 520 992 538 504 1033 1041 568 943 533         983 564 1021 494 481 1033 995 525 987 536         987 547 986 548 479 1082 953 545 481 1063         497 1025 500 1053 547 1037 490 995 2973 7035 0
531 1082 430 1011 494 1030 499 1073 486 1028     987 610 972 472 533 1011 979 534 990 538         989 537 986 550 486 1047 985 548 978 539         989 551 980 574 489 1053 983 549 454 1069         480 1048 459 1048 494 1042 466 1037 2999 7139 0

463 1025 513 1011 495 1031 506 1031 507 1021     496 1031 992 534 494 1056 486 1055 1000 548     1040 520 469 1047 471 1031 465 1051 975 542     981 553 487 1038 490 1039 985 543 493 1044         490 1062 484 1041 499 1037 478 1065 2984 7035 0
499 1055 462 1024 540 993  499 1080 457 1071     533 969 1006 545 476 1058 475 1018 989 552         975 539 486 1052 487 1030 493 1043 990 536         989 551 486 1046 481 1081 973 559 473 1059         473 1053 468 1028 480 1044 501 1032 2992 7072 0
496 1052 489 1107 422 1034 485 1053 492 1023     472 1049 969 533 493 1046 493 1027 998 536         990 534 498 1043 507 1047 490 1068 963 542         989 551 480 1048 454 1039 1065 503 456 1044     488 1044 485 1034 486 1040 502 1031 2995 7139 0

493 1025 499 1034 492 1028 501 1059 972  555     1030 504 504 1039 482 1044 476 1047 468 1035     493 1034 989 543 502 1027 991 567 962 545         477 1055 483 1045 488 1059 495 1140 894 548     480 1116 414 1042 470 1043 535 990 2987 7056 0
509 1056 475 1037 509 1056 492 1017 1052 467     972 551 477 1031 499 1033 498 1050 475 1035     504 1026 992 542 489 1078 981 542 977 638         380 1061 495 1081 446 1018 504 1036 970 549     483 1040 494 1043 479 1041 486 1045 2993 7087 0
468 1147 398 1022 486 1024 503 1034 1000 531     992 536 491 1036 497 1048 482 1057 494 1037     498 1041 1021 507 488 1043 957 548 999 517         492 1048 487 1044 478 1048 479 1040 1004 537     481 1041 509 1035 498 1064 475 1042 3000 7031 0

Translating like this:
500 1000 => 0
1000 500 => 1
3000 => 7000 => X (Trailing)

Code:
00000 11011 11011 11010 0000X
00000 11011 11011 11010 0000X
00000 11011 11011 11010 0000X

00000 01001 10001 10010 0000X
00000 01001 10001 10010 0000X
00000 01001 10001 10010 0000X

00000 10000 01011 00001 0000X
00000 10000 01011 00001 0000X
00000 10000 01011 00001 0000X

So everytime i press the same button, different codes are sending.
 
Reply
#12
Your first code is not very clear Wink
 
Reply
#13
(12-31-2013, 12:52 AM)curlymo Wrote: Your first code is not very clear Wink
True Wink, but do you recognise this behavior?
 
Reply
#14
Could be rolling code, but don't think that's obvious for cheap switches.
 
Reply
#15
But how to translate this into a protocol?
 
Reply
#16
If this i currently your output, you don't. If you can get clear similar codes, you can.
 
Reply
#17
I have made some kind of protocol: http://pastebin.com/LeTKZcf0
I can switch all four receivers on and off Smile

In the attachment i have added an Excel sheet with all the codes I receive from the buttons.
When i press a button ones, three the same codes are sending.
When i press the same button again, other code is sending.
There are four different codes sending and then the first code has been sending again when i keep pressing the same button.

In this protocol i am only sending the first part of the code and that is working. But it's only working for my remote control. An other remote will send other codes.

But, how can i translate the receive code into the correct unit?
How does the parseCode or parseBinary works?


Attached Files
.xlsx   Quigg.xlsx (Size: 94.39 KB / Downloads: 34)
 
Reply
#18
Check the protocol development page on the pilight website.
 
Reply
#19
When looking at the excel sheet i see a some clear patterns:
- On/Off @AD + AE
I'm questioning if you didn't swap 4 ON and OFF
- Unit / ID / Header @A-I
- Unit / ID @AP - AU
- All @AQ, AR, AU
In case of the ALL these are the only two codes in which these pulses are low.
 
Reply
#20
I try to improve this protocol

Code:
void quiggParseRaw(void){
    int i=0;
    for(i=0;i<quigg->rawlen;i++) {
        printf("%d, ", quigg->raw[i]);
    }
    printf("\n");
}

Give as output:

Code:
[Jan 11 13:44:17:770529] pilight-daemon: DEBUG: called QUIGG parseRaw()
conradRSLSwParseRaw: 491, 1056, 475, 1033, 520, 1011, 505, 1023, 1015, 542, 968, 544, 498, 1048, 490, 1031, 488, 1053, 467, 1081, 453, 1053, 980, 548, 478, 1044, 1007, 530, 970, 552, 496, 1043, 480, 1049, 501, 1038, 467, 1078, 954, 554, 478, 1056, 471, 1048, 1007, 516, 490, 1050, 2975, 7075

but

Code:
void quiggParseCode(void) {
    int x = 0;

    for(x=0; x<quigg->rawlen; x++) {
        printf("%d", quigg->code[x]);
    }

gives output:

Code:
pilight-daemon: DEBUG: called QUIGG parseCode()
11011111111111111111111111111111111111111111111111

What is wrong.

I also try to set LSB to 1,2,3 and 4 but not a improvement.
 
Reply
  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Brennenstuhl RCR CE1 1011 with QUIGG GT9000 Protocol scootermacro 1 214 06-27-2019, 06:20 PM
Last Post: scootermacro
  QUIGG GT9000 (Globaltronics/ALDI) NeoFlo 138 64,767 04-13-2019, 05:44 PM
Last Post: fourty2
  Weather Station Globaltronics GT-WT-01 Prutsky 13 6,736 04-09-2018, 07:34 PM
Last Post: NevelS
  Quigg GT-1000 maartenh 53 24,039 12-05-2016, 03:13 PM
Last Post: Klaus
  quigg gt7000 Dimmer wchristi 11 7,928 04-30-2015, 09:25 AM
Last Post: wo_rasp
  Quigg Screens curlymo 6 3,875 01-31-2015, 07:33 PM
Last Post: curlymo

Forum Jump:


Browsing: 1 Guest(s)