• 10 dec 2017: forum version update. In case of issues use this topic.
  • 30 nov 2017: pilight moved servers. In case of issues use this topic.
Hello There, Guest! Login Register


Kaku PAT-103 / PAR-1000
#1
I am trying to get started with pilight. The installation guide and the wiki are great tools, but I am stuck.

Hardware:
- Klik aan Klik uit, PAT-103 sender, PAR-1000 switch
- GPIO Sender and receiver: Superheterodyne and Low Pass Filter for the receiver

From the supported list I know my hardware is supported and I would expect the following protocols. kaku_switch or kaku_switch_old.

But after I run pilight-receive when the receiver is connected I get the following output:

Code:
{
        "code": {
                "id": "F14",
                "unit": 31,
                "state": "off"
        },
        "origin": "receiver",
        "protocol": "rev_switch",
        "uuid": "033B-00-00-3B-000300",
        "repeats": 1
}
A pilight-debug returns:
Code:
hardware:       433gpio
pulse:          4
rawlen:         50
binlen:         12
pulselen:       324

Raw code:
648 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 1296 324 324 972 1296 324 324 972 1296 324 324 11016
Binary code:
111111111000

I cannot get the sender to work. How should I set my config.json file (correct protocol / ID / UNIT) ? I've tried a lot of different combinations.

/edit: just had a breakthrough:
Code:
pilight-send -p raw -c "648 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 324 972 1296 324 324 972 1296 324 324 972 1296 324 324 11016"

Works sending the on signal to the PAR-1000 switch.

/edit2:format
 
Reply
  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Quigg GT-1000 maartenh 55 29,425 07-28-2020, 03:21 PM
Last Post: pgScorpio
  [Solved] Quigg GT-1000 leaving transmitter ON VrahoK 11 1,071 12-22-2019, 12:17 AM
Last Post: VrahoK
Lightbulb [Fully Supported] Kaku Door sensor (AMST-606) geerttttt 53 28,415 10-19-2019, 06:26 PM
Last Post: curlymo
  KAKU Door contact (AMST-606) patrick van der tol 19 9,204 02-28-2017, 12:51 AM
Last Post: wo_rasp
  [Fully Supported] KAKU ABST-604 (dusk/dawn sensor) Netopyr 15 8,573 03-04-2016, 05:43 PM
Last Post: Niek
  [Fully Supported] Arctech Dimmer (KaKu) fhp 107 48,161 01-02-2016, 05:26 PM
Last Post: kniazio
  KaKu pir sensor undetectable Kucuk 3 2,456 02-14-2015, 08:52 PM
Last Post: curlymo
  KaKu ACD-1000R plus AFR-060 pijnjoh 8 4,114 05-16-2014, 11:23 PM
Last Post: curlymo
  [Impossible] Kaku old dimmer reinder83 11 6,698 02-09-2014, 01:46 PM
Last Post: effjey
  Alecto WS-1000 koffie 1 2,393 12-30-2013, 10:19 PM
Last Post: curlymo

Forum Jump:


Browsing: 1 Guest(s)